ConnectivityNode

Type: object

Connectivity nodes are points where terminals of AC conducting equipment are connected together with zero impedance.

root ConnectivityNode.SvVoltage
Type: array

State variable for voltage.

 No Additional Items

Each item of this array must be:

root ConnectivityNode.SvVoltage SvVoltage.json
Type: object

State variable for voltage.

root ConnectivityNode.SvVoltage SvVoltage SvVoltage.angle
Type: object or number

The voltage angle of the topological node complex voltage with respect to system reference.

root ConnectivityNode.SvVoltage SvVoltage SvVoltage.angle multiplier
Type: enum (of string) Default: "none"

nan

Must be one of:

  • "p"
  • "n"
  • "micro"
  • "m"
  • "c"
  • "d"
  • "k"
  • "M"
  • "G"
  • "T"
  • "none"
  • "y"
  • "z"
  • "a"
  • "f"
  • "da"
  • "h"
  • "P"
  • "E"
  • "Z"
  • "Y"

root ConnectivityNode.SvVoltage SvVoltage SvVoltage.angle unit
Type: enum (of string) Default: "deg"

nan

Must be one of:

  • "none"
  • "m"
  • "kg"
  • "s"
  • "A"
  • "K"
  • "mol"
  • "cd"
  • "deg"
  • "rad"
  • "sr"
  • "Gy"
  • "Bq"
  • "degC"
  • "Sv"
  • "F"
  • "C"
  • "S"
  • "H"
  • "V"
  • "ohm"
  • "J"
  • "N"
  • "Hz"
  • "lx"
  • "lm"
  • "Wb"
  • "T"
  • "W"
  • "Pa"
  • "m2"
  • "m3"
  • "mPers"
  • "mPers2"
  • "m3Pers"
  • "mPerm3"
  • "kgm"
  • "kgPerm3"
  • "WPermK"
  • "JPerK"
  • "ppm"
  • "rotPers"
  • "radPers"
  • "VA"
  • "VAr"
  • "cosPhi"
  • "Vs"
  • "V2"
  • "As"
  • "A2"
  • "A2s"
  • "VAh"
  • "Wh"
  • "VArh"
  • "VPerHz"
  • "HzPers"
  • "character"
  • "charPers"
  • "kgm2"
  • "dB"
  • "WPers"
  • "lPers"
  • "dBm"
  • "h"
  • "min"
  • "Q"
  • "Qh"
  • "ohmm"
  • "APerm"
  • "V2h"
  • "A2h"
  • "Ah"
  • "count"
  • "ft3"
  • "m3Perh"
  • "gal"
  • "Btu"
  • "l"
  • "lPerh"
  • "lPerl"
  • "gPerg"
  • "molPerm3"
  • "molPermol"
  • "molPerkg"
  • "sPers"
  • "HzPerHz"
  • "VPerV"
  • "APerA"
  • "VPerVA"
  • "rev"
  • "kat"
  • "JPerkg"
  • "m3Uncompensated"
  • "m3Compensated"
  • "WPerW"
  • "therm"
  • "onePerm"
  • "m3Perkg"
  • "Pas"
  • "Nm"
  • "NPerm"
  • "radPers2"
  • "WPerm2"
  • "JPerkgK"
  • "JPerm3"
  • "VPerm"
  • "CPerm3"
  • "CPerm2"
  • "FPerm"
  • "HPerm"
  • "JPermol"
  • "JPermolK"
  • "CPerkg"
  • "GyPers"
  • "WPersr"
  • "WPerm2sr"
  • "katPerm3"
  • "d"
  • "anglemin"
  • "anglesec"
  • "ha"
  • "tonne"
  • "bar"
  • "mmHg"
  • "M"
  • "kn"
  • "Vh"
  • "Mx"
  • "G"
  • "Oe"
  • "WPerA"
  • "SPerm"
  • "onePerHz"
  • "VPerVAr"
  • "ohmPerm"
  • "kgPerJ"
  • "JPers"
  • "m2Pers"
  • "JPerm2"
  • "KPers"
  • "PaPers"

root ConnectivityNode.SvVoltage SvVoltage SvVoltage.angle value
Type: number Default: null

nan

root ConnectivityNode.SvVoltage SvVoltage SvVoltage.v
Type: object or number

The voltage magnitude at the topological node. The attribute shall be a positive value.

root ConnectivityNode.SvVoltage SvVoltage SvVoltage.v unit
Type: enum (of string) Default: "V"

nan

Same definition as unit

root ConnectivityNode.SvVoltage SvVoltage SvVoltage.v value
Type: number Default: null

nan

root ConnectivityNode.SvVoltage SvVoltage SvVoltage.phase
Type: enum (of string)

If specified the voltage is the line to ground voltage of the individual phase. If unspecified, then the voltage is assumed balanced.

Must be one of:

  • "A"
  • "B"
  • "C"
  • "N"
  • "s1"
  • "s2"

root ConnectivityNode.SvInjection
Type: array

The SvInjection reports the calculated bus injection minus the sum of the terminal flows. The terminal flow is positive out from the bus (load sign convention) and bus injection has positive flow into the bus. SvInjection may have the remainder after state estimation or slack after power flow calculation.

 No Additional Items

Each item of this array must be:

root ConnectivityNode.SvInjection SvInjection.json
Type: object

The SvInjection reports the calculated bus injection minus the sum of the terminal flows. The terminal flow is positive out from the bus (load sign convention) and bus injection has positive flow into the bus. SvInjection may have the remainder after state estimation or slack after power flow calculation.

root ConnectivityNode.SvInjection SvInjection SvInjection.pInjection
Type: object or number

The active power mismatch between calculated injection and initial injection. Positive sign means injection into the TopologicalNode (bus).

root ConnectivityNode.SvInjection SvInjection SvInjection.qInjection
Type: object or number

The reactive power mismatch between calculated injection and initial injection. Positive sign means injection into the TopologicalNode (bus).

root ConnectivityNode.SvInjection SvInjection SvInjection.phase
Type: enum (of string)

The terminal phase at which the connection is applied. If missing, the injection is assumed to be balanced among non-neutral phases.

Same definition as SvVoltage.phase

root IdentifiedObject.description
Type: string

The description is a free human readable text describing or naming the object. It may be non unique and may not correlate to a naming hierarchy.

root IdentifiedObject.aliasName
Type: string

The aliasName is free text human readable name of the object alternative to IdentifiedObject.name. It may be non unique and may not correlate to a naming hierarchy.
The attribute aliasName is retained because of backwards compatibility between CIM relases. It is however recommended to replace aliasName with the Name class as aliasName is planned for retirement at a future time.

root IdentifiedObject.mRID
Type: string

Master resource identifier issued by a model authority. The mRID is unique within an exchange context. Global uniqueness is easily achieved by using a UUID, as specified in RFC 4122, for the mRID. The use of UUID is strongly recommended.
For CIMXML data files in RDF syntax conforming to IEC 61970-552, the mRID is mapped to rdf:ID or rdf:about attributes that identify CIM object elements.

root IdentifiedObject.name
Type: string

The name is any free human readable and possibly non unique text naming the object.